Here is a review of the restoration & improvements I have done. I started the project thinking that I would replace the steering, steering wheel and all the electrical. I got into the project and met multiple glaring deficiencies that I couldn't ignore.
So far I have:
-Replaced the aft 3 removable panels with Starboard, TAP plastics did the cutting
-Restored the dash board, gauges and added all new switches
-Replaced the cable steering with Seastar Hydraulic ram, helm pump and hoses
-New wiring, battery cables, primary and running (14ga)
-Replaced the cable boot and fitted a custom housing (ABS) to cover the figure 8 size hole (SS Screws for future needs)
-Replaced the Stern light/housing and the deck light
-Replaced the bilge pump and added a float switch to the system, both devices run to an independent bilge switch with a breaker (also fused at DC panel), with LED indication of AUTO/OFF/Manual (Manual is momentary on, stops when not depressed)
-Installed a DC fuse panel
-Installed 4 way battery switch (the old existing one was bypassed and not functional) with an inline 50 AMP breaker in-between switch & panel
-Installed two 175AMP MRBF fuses on either positive battery terminal (Thanks for the tip AJ & Dev)
-2020* I replaced the old 115 mercury with a DF90 2020 - Miss the two smoke
I have a few more tasks:
-Terminate the panel and make pretty (at least 3 hours)
-Bolt on the new bow light & wire it
-Determine VHF needs - I removed the old one, haven't decided what size antenna to reinstall
-Decide what to do with the horn, rewire it to the push button or delete?
-Mount FF/Plotter maybe buy a new unit if there are any deals?
I will post more in detail about the fun parts of the job when I have the opportunity.
:beerchug:
Nice work, it looks great!
Out of room adding photos
Very clean work. Looks great! I like the new profile photo too. :beerchug:
Nice summary. Well done on the work. Folks will be getting ideas... :beerchug:
Nice work! Projects always seem to grown when think you're just going to do a few things, then next minute you've gone through the whole boat, but it's all worth it.
Thank you. Love the work.
Powered up and ready to go.
The dash looks great!
I decided to make service in the future very, very easy.. My hat is off to the guys Who can make a panel look like a piece of art.
And check out this backlit, for position switch. I love it and would highly recommend. It is waterproof.
It's amazing how much more room you have for helm wiring than I have in my Sea Ranger.
Your whole project is coming along and looks great!
Quote from: DeskJockey on December 02, 2021, 06:51:44 PM
It's amazing how much more room you have for helm wiring than I have in my Sea Ranger.
Your whole project is coming along and looks great!
That is interesting, I am curious to see the difference. I really appreciate the feedback, this is definitely the rewarding part, seeing everything come together.
Fantastic transformation, Marshall! That's an impressively long list of projects, particularly given the scale of many of them!
Dave
Awesome! I like the boot replacement, is that custom?
Joe
All worthwhile things to make your boat more trouble free when you want to be out enjoying it. Why don't you come to Va and work on my latest project ?
You are doing a good job. Get it done and back on the water.
Quote from: DARice on December 03, 2021, 09:47:54 AM
Fantastic transformation, Marshall! That's an impressively long list of projects, particularly given the scale of many of them!
Dave
Thanks Dave, look forward to show you in person.
Quote from: beancounter on December 03, 2021, 01:22:26 PM
All worthwhile things to make your boat more trouble free when you want to be out enjoying it. Why don't you come to Va and work on my latest project ?
You are doing a good job. Get it done and back on the water.
Hey, thanks Bean! Well, I haven't seen the Blue Ridge Mountains.. What are you working on?
Quote from: Crackerbox on December 03, 2021, 11:58:40 AM
Awesome! I like the boot replacement, is that custom?
Joe
Hey thanks! Yes it is custom, I used 1/8" ABS to make a base plate for the cable boot. Life seal and some stainless steel screws.
Quote from: DeskJockey on December 02, 2021, 06:51:44 PM
It's amazing how much more room you have for helm wiring than I have in my Sea Ranger.
My thoughts too! I'm currently trying to clean mine up.
The only difference I see behind the helm is the absence of the little starboard box used to house the steering rack and electronics.This project is using the entire panel.
All my drafts before I got everything the way I wanted..
Also, the As Built, which I would like to do on the computer some how, eventually. I ran out of room for the cuddy light, but it's pretty easy to see and runs straight to the panel in wire loom.
New VHF Mount and antenna. New plate's holes didn't match to I made another custom backplate.
Delete
What are you using for your dash material, how are you cutting it, and what are you using to secure it?
Quote from: kriznol on December 14, 2021, 10:37:43 PM
What are you using for your dash material, how are you cutting it, and what are you using to secure it?
1/8" ABS Plastic, one side smooth other side textured. Textured side out. I used a root zip style Dewalt, not very effective but the oscillating multi tool was great. I almost bought a jigsaw for this because that would be the perfect tool but didn't need to. Sanded the edges with a rasp , 180 and finally 120 grit. Fastened the ABS with stainless steel screws and life seal on the needed seals.
Also, I used a heat gun to get the plastic the right bend when needed.
I opted to reuse the black rocket pods for the time being.
I am getting very close to detailing.. I added some cleanliness to the port side dash. The electrical is done, minus labeling with my label maker. I WAS able to get the trim back in the slot, it hasn't shrunk and I think I get the idea now and can find a new replacement.
Got out for another function test. Feeling good about everything. I'll drop a few more photos of the progress, when it starts warming up and I can detail the boat, it will clean up nicely I think. Still haven't landed on a below gunwale rod storage replacement, if any. Seats are looking tired to me, Might have to find something cool to replace..With the help of you guys maybe. Also, I am testing a 4' little giant, we'll see.
Nice job on the electrical in the cuddy.
Mine looks like such a nightmare I can't imagine trying to rework all the wires!
Quote from: jaunty on December 25, 2021, 12:06:56 PM
Nice job on the electrical in the cuddy.
Mine looks like such a nightmare I can't imagine trying to rework all the wires!
Thanks! Really glad that part is done!
Well done, sir. :clap:
Very clean. Looks great!
Much appreciated!
Looks good and cool you got it back on the water👍
Thanks AJ, you blazed the trail!
Very nice job. I'm looking to add a second battery and I noticed that you have yours on port and starboard, though you have a kicker. How has that worked out for you with weight distribution? And, what size/weight is your Honda kicker?
Quote from: Fester on January 02, 2022, 01:26:52 PM
Very nice job. I'm looking to add a second battery and I noticed that you have yours on port and starboard, though you have a kicker. How has that worked out for you with weight distribution? And, what size/weight is your Honda kicker?
Hey Thanks, I had them both on starboard and moved them back to either side. It leans a little more to port now without anyone onboard and no anchor or gear onboard. Once I get all the gear and anchor onboard it's perfect. I'm 225 so the boat is going to list wherever I step 🤷♂️. It has become a balance issue more than anything and trim tabs won't do much when I'm trolling unfortunately.
Quote from: Pdxmgunner on January 02, 2022, 02:57:13 PM
Quote from: Fester on January 02, 2022, 01:26:52 PM
Very nice job. I'm looking to add a second battery and I noticed that you have yours on port and starboard, though you have a kicker. How has that worked out for you with weight distribution? And, what size/weight is your Honda kicker?
Hey Thanks, I had them both on starboard and moved them back to either side. It leans a little more to port now without anyone onboard and no anchor or gear onboard. Once I get all the gear and anchor onboard it's perfect. I'm 225 so the boat is going to list wherever I step 🤷♂️. It has become a balance issue more than anything and trim tabs won't do much when I'm trolling unfortunately.
Honda is a 8hp at 95lbs I believe.
Cuddy door swapped.
You are doing a nice job.
Very nice! :clap:
Thanks a lot guys! I am ready to get my gear together for the spring salmon run. I think my winter project has concluded.
Quote from: Pdxmgunner on January 21, 2022, 04:42:32 PM
Thanks a lot guys! I am ready to get my gear together for the spring salmon run. I think my winter project has concluded.
That's great news bud! Good work
Big, Big thanks to all you guys. Appreciate the help and the schematics for me to get my bearings..
Disposable
Dev
Dv
AJ
Miester
DeskJ
Jaunty
Mooch
I'm going to miss someone and everyone on here has been supportive and helpful. So cheers, go team Arima.
Awesome man, nows the best part, enjoying it! :gone_fishing:
Dude, no doubt.. I got out in the sun today and everything us dialed. Feels good!
Quote from: Pdxmgunner on January 21, 2022, 04:42:32 PM
... I think my winter project has concluded.
What?! You've got TONS of work left!
Just kidding! Go have a busy fishing season and use it as much as you can. Resist the urge to project until the season is over, the work can become addictive but without the fishing it starts to wear on you (at least it did for me). Stock up on spare parts, keep an eye on your trailer, and start calling your fishing buddies (so they can hassle you when you're threatening to mow the lawn or wash to cat). Here's to a busy season :beerchug:
Nice work looks great!!
Now time for some Arima therapy.
Dev